Material estimating.
Coverage rates, unit conversions, and mortar and sand math for brick, stone, and block. Use them to size an order before you call. Measure your square footage, pick your material, and read the rate off the tables below.
These figures are planning estimates. Coverage varies with pattern, joint size, cuts, and waste. Estimates from blueprints are a courtesy, not a guarantee. Double-check quantities with your mason before ordering.
General measurement units
Start here. Convert your job dimensions into the units our coverage rates use: tons, cubic yards, and square feet.
- One ton
- 2,000 lb The unit full-bed stone is priced and sold by.
- One cubic yard
- 27 cu ft A 3' × 3' × 3' volume, used for sand and fill.
- Square feet
- L × W 10' × 10' = 100 sq ft. Subtract openings.
Brick
Coverage depends on the brick size. Find your size below for bricks per square foot, then use the mortar, sand, and tie rates to complete the order.
- 4.5
- Bricks / sq ft
- Laid flat for paving or hearths (solid brick).
- ~7 bags
- Mortar / 1,000 brick
- About 143 bricks per bag.
- ~1 yd
- Sand / 1,000 brick
- Mason's sand for the mortar mix.
- 1 : 10
- Wall ties
- One tie per 10 bricks, 100 per 1,000.
Coverage by brick size
depth × height × length- Modular 3 5/8" d × 2 1/4" h × 7 5/8" l 6.86 / sq ft
- Standard 3 5/8" d × 2 1/4" h × 8" l 6.55 / sq ft
- Engineer 3 5/8" d × 2 3/4" h × 8" l 5.5 / sq ft
- King 3" d × 2 5/8" h × 9 5/8" l 4.8 / sq ft
- Queen 3" d × 2 3/4" h × 8" l 5.5 / sq ft
- Closure 3 5/8" d × 3 5/8" h × 7 5/8" l 4.5 / sq ft
- Wall unit 3 5/8" d × 7 5/8" h × 7 5/8" l 2.25 / sq ft
- Big John 3" d × 2 5/8" h × 8 5/8" l 5.33 / sq ft
- Utility 3 5/8" d × 3 5/8" h × 11 5/8" l 3 / sq ft
- Norwegian 3 5/8" d × 2 3/4" h × 11 5/8" l 3.84 / sq ft
- Norman 3 5/8" d × 2 1/4" h × 11 5/8" l 4.57 / sq ft
- Executive 3 x 10 3" d × 3" h × 10" l 4.11 / sq ft
- Roman 3 5/8" d × 1 5/8" h × 11 5/8" l 6 / sq ft
- 4 x 16 3 5/8" d × 3 5/8" h × 15 5/8" l 2.25 / sq ft
- 8 x 16 3 5/8" d × 7 5/8" h × 15 5/8" l 1.125 / sq ft
Coverage assumes a 3/8" mortar joint and is calculated from the dimensions shown. Solid brick laid flat for paving or hearths runs about 4.5 per sq ft.
Natural stone
Full-bed stone sells by the ton; thin veneer and flagstone sell by coverage. Match your application to the group below.
Full-dimensional
- Per pallet
- ~1.5 tons
- Building stone (3–5")
- 35–40 sq ft / ton
- Per ton
- 3 bags mortar + 1/2 yd sand
Thin veneer
- Per square foot
- under 15 lb
- Per pallet
- ~125 sq ft
- Per EZ Pac Mini
- ~8 sq ft
Flagstone
- Thin patio (3/8–1")
- 150–180 sq ft
- Patio grade (1–2")
- 100–120 sq ft
- Slabs (2–3")
- 75–100 sq ft
Thin brick and natural stone must be thoroughly washed before installation. For thin veneer, see the Natural Stone Thin Veneer tech sheet (PDF, opens in a new tab).
Block
Concrete masonry unit (CMU) yields, coverage, and the masonry-and-sand rate for a standard run.
Concrete masonry units (CMU)
- Per pallet
- ~1.5 tons (8" block ~90 pcs, 4" block ~180 pcs)
- Coverage
- 1.125 / sq ft
- Per ton
- 3 bags mortar + 1/2 yd sand
- Per 300 blocks
- 6 bags masonry + 1 yd sand
Guides, brochures & disclaimers
Product brochures with the full range of sizes and finishes, plus the estimating and material disclaimers that go with them.
- Thin Brick Brochure (PDF, opens in a new tab)
- Thin Stone Brochure (PDF, opens in a new tab)
- Handmade Brick Brochure (PDF, opens in a new tab)
- Natural Stone Thin Veneer tech sheet (PDF, opens in a new tab)
- Accurate Material Estimation (PDF, opens in a new tab)
- Brick Blending Disclaimer (PDF, opens in a new tab)
- Guidelines for Installing Thin Used Antique Brick (PDF, opens in a new tab)
- Natural Stone Disclaimer (PDF, opens in a new tab)
- Painted Brick Disclaimer (PDF, opens in a new tab)
Prefer we do the math?
Every product page has a coverage calculator. Enter your square footage and it adds up packages, pieces, and cost, with an optional 10% waste buffer.
Browse products